Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
Just about everyone will have his or her own conception on the subject of Installing A Bathtub.
Mounting a bath tub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently easily accessible, the job can move quickly; if you have to open up a wall to eliminate the old bathtub as well as place the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will need a helper to move out the old tub and also set in the brand-new one. Make sure you have qualified on your own for the task and also are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is far better to consider using one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will aid you set up a brand-new bath tub in your shower room if you have actually already gotten a brand-new bathtub as well as do not need to change the setup of your previous water pipes.
Your devices as well as material checklist must comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather problematic because of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin ensuring that the washers remain in place in between the faucet and also the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former kind must be connected to the faucet ends first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Making use of both wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bath tub until the spirit level reads level.
To install taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other tap.
Switch on the water and check all joints and also new pipework for leaks and tighten them if essential. Fill up the bath tub and additionally examine the overflow outlet as well as the normal electrical outlet for leaks.
Finally, repair the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub needs to wait till the bathtub has been used at the very least once as this will settle it into its last setting.
Getting ready for the Setup
Firstly, the supporting structure supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you use all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall surface between the bath as well as the tiling, bring about problems with wetness and possible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are marketed in tubes and cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealant can split fairly very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place a remark further down. We will be pleased to see your responses about this blog posting. We hope to see you back again in the near future. Liked our post? Please share it. Let another person discover it. I value reading our article about How to Install a Bathtub.
Top-notch care? Dial. Report this page